Opticlear

Opticlear

Features:

OptiClear (Original)

OptiClear is the original, award winning, nontoxic, non-flammable, biodegradable solvent from National Diagnostics. OptiClear is intended for the removal of wax, pitch, flux, grease, resin and solvent soluble resists from optical and electronic components of glass, ceramic or meta.

OptiClear may be substituted directly for toluene, xylene or chlorinated hydrocarbons, such as trichloroethylene (TCE), in batch-type or ultrasonic cleaners with no alteration in protocol. OptiClear removes wax adhered to lenses, optical components, polished wafers or printed circuit boards.

OptiClear has high solvency power, yet it will not affect metal or metal alloy. OptiClear also has a neutral pH, so it will not stain glass. The water content of OptiClear is less than 50 ppm. It is miscible in all proportions with acetone, ethanol, and isopropanol, any of which may be used as a post-wash.

 

OptiClear S

OptiClear S is a non-flammable, odorless degreaser that removes light oil from optics and electronics components. OptiClear S is nonconductive and leaves no residue. OptiClear S can also be used to remove wax and pitch; although the necessary soaking time is longer than that required for the original OptiClear. OptiClear S has a higher flash point and evaporates more slowly than OptiClear E

 

OptiClear S2

OptiClear S2 is a non-flammable, odorless degreaser that removes light oil from optics and electronics components. OptiClear S2 is nonconductive and leaves no residue. OptiClear S2 can also be used to remove wax and pitch; however, the necessary soaking time is longer than that required for OptiClear Original. OptiClear S2 has a higher flash point than OptiClear S but evaporates more slowly than Opticlear S.

 

OptiClear E

OptiClear E is an odorless cleaning solvent for optical and electronic components. OptiClear E is our fastest evaporating OptiClear formulation, and it leaves no residue. This eliminates the need for a post wash. OptiClear E is also nonconductive. OptiClear E can be used to remove wax and pitch; however, the necessary soaking time is longer than that required for the original OptiClear.

 

OptiClear W

OptiClear W is a non-flammable, biodegradable solvent intended to remove grease and oil from optical and electronic components. OptiClear W is miscible in all proportions with water. This eliminates the need for a solvent dip, since water can be used as a post-wash.

 

OptiClear R

OptiClear R is a non-flammable, biodegradable, water-based solvent intended as an acetone replacement for cleaning optical and electronic components. OPtiClear R is nonconductive and can be used to rinse away oily film and light grease from glass, ceramic or metal without leaving any residue. OptiClear R is non-aggressive and does not attack metal, glass or plastic.

Specifications:

	NDIOE-101	NDIOE-102	NDIOE-104	NDIOE-105	NDIOE-106	NDIOE-107
Boiling Point	355° F	180° F	244- 284° F	376 - 401° F	396° F	424 - 484° F
Melting Point	N/A	N/A	< - 76° F	< -76° F	-11 F	< -76° F
Vapour Pressure	6.0 mm HG @ 25° C	58 mm Hg @ 38° C	36 mmHg @ 68° F	1 mmHg @ 68° F	0.5 @ 77° F	< 0.1 mmHg @ 68° F
Vapour Density	4.94 (air = 1)	1.5 (air = 1)	3.9	5.9	3.4	5.9
% Volatile by Volume	100	100	100	100	100	100
Evaporation Rate	N/A	2.0 (Bu Acetate = 1)	1.6 (n-Bu Acetate=1)	< 0.1 (n-BuAcetate=1)	0.06 (BuAc = 1)	< 0.01 (n-Bu Ac=1)
Solubility in Water	Insoluble	Soluble	< 0.01% @ 77° F	< 0.01% @ 77° F	Miscible in water	< 0.01% @ 77 F
pH	N/A	N/A	N/A	N/A	7.7	N/A
Specific Gravity (H20 = 1)	0.85 @ 25° C	0.94	0.72 @ 60° F	0.77 @ 60° F	1.03	0.79 @ 60° F

 

MSDS Sheets

NDIOE-101: Opticlear Original NDIOE-102: Opticlear R
NDIOE-104: Opticlear E
NDIOE-105: Opticlear S
NDIOE-106: Opticlear W
NDIOE-107: Opticlear S2